Were you hunting for content about How to Install a Bathtub?
Setting up a bath tub isn't specifically rocket science, however it does need strong plumbing, carpentry, as well as often, tiling skills. Changing an old tub with a brand-new one is additionally a reasonably hard task. If the old tub is easily easily accessible, the task can relocate easily; if you need to open a wall to eliminate the old bathtub and also position the brand-new bath tub, the job is much harder. In either case, the job is within a house handyman's abilities, although you will certainly require a helper to move out the old tub and also embeded in the new one. Ensure you have qualified on your own for the work and also fit trying it. Rather than working with a contractor to take control of a halfway-completed job, it is better to consider employing one before you start. Opportunities are you may need a professional plumber to make tube links.
This short article will aid you set up a new bathtub in your shower room if you have actually already bought a brand-new bathtub as well as do not need to change the plan of your previous water supply pipelines.
Your devices and product list ought to comprise the following:
Planning for the Setup
Firstly, the sustaining frame provided with the bathroom ought to be fitted (if needed) according to the manufacturer's guidelines. Next, fit the taps or mixer to the bathtub. When suitable the tap block, it is important to make certain that if the tap features a plastic washing machine, it is fitted in between the bathroom and also the taps. On a plastic bath, it is additionally practical to fit a sustaining plate under the faucets system to prevent strain on the bath tub.
Fit the versatile faucet connectors to the bottom of both taps making use of 2 nuts as well as olives (occasionally supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the outlet via the hole in the bath. Make use of the nut supplied by the manufacturer to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the adaptable overflow pipe to the overflow electrical outlet. After that, screw the pipe to the overflow face which ought to be fitted inside the bathroom. Make sure you utilize all of the supplied washing machines.
Link the catch to the bottom of the waste outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Connect the bottom of the overflow tube in a similar manner.The bathroom need to now prepare to be suited its final setting.
Removing Old Touches
If you require to change old taps with brand-new ones as a part of your installment, then the first thing you must do is disconnect the supply of water. After doing so, turn on the taps to drain pipes any water staying in the system. The procedure of removing the existing faucets can be fairly problematic because of the limited access that is frequently the situation.
Make use of a basin wrench (crowsfoot spanner) or a tap tool to undo the nut that connects the supply pipes to the taps. Have a fabric prepared for the continuing to be water that will come from the pipes. When the supply pipelines have actually been eliminated, utilize the exact same device to loosen the nut that holds the taps onto the bath/basin. You will certainly need to stop the solitary faucets from turning throughout this procedure. Once the faucets have been eliminated, the holes in the bath/basin will certainly have to be cleaned up of any kind of old securing compound.
Before going on to fit the brand-new taps, compare the pipeline links on the old faucets to the new taps. If the old faucets are longer than the brand-new faucets, then a shank adapter is needed for the new taps to fit.
Setting up the Bathtub
Using both wood boards under its feet, place the tub in the called for position. The wooden boards are valuable in equally spreading the weight of the tub over the location of the boards as opposed to concentrating all the weight onto 4 tiny points.
The next goal is to guarantee that the tub is leveled all round. This can be attained by examining the level and readjusting the feet on the bathtub till the level reviews level.
To install faucets, fit the bottom of the furthest adaptable faucet port to the proper supply pipeline by making a compression sign up with; then do the exact same for the other tap.
Switch on the supply of water as well as inspect all joints and brand-new pipework for leaks and also tighten them if needed. Fill up the tub as well as likewise inspect the overflow electrical outlet as well as the typical electrical outlet for leaks.
Finally, repair the bathroom paneling as defined in the supplier's user's manual. Tiling as well as sealing around the bath tub ought to wait up until the bathtub has been used at least when as this will settle it into its last placement.
Fitting New Touches
If the tails of the new taps are plastic, then you will certainly require a plastic connector to avoid damages to the string. One end of the port fits on the plastic tail of the tap and the various other end gives a connection to the existent supply pipes.
If you require to fit a monobloc, after that you will need lowering couplers, which links the 10mm pipe of the monobloc to the conventional 15mm supply pipe.
Next, place the faucet in the mounting hole in the bath/basin making sure that the washers remain in place between the faucet and also the sink. Secure the faucet in place with the manufacturer supplied backnut. When the tap is firmly in place, the supply pipes can be attached to the tails of the taps. The faucets can either be linked by utilizing corrugated copper piping or with typical tap adapters. The former kind must be connected to the faucet finishes first, tightening up just by hand. The supply pipes can later be attached to the other end. Tighten up both ends with a spanner after both ends have actually been linked.
Tiling Around the Bathtub
In the area where the bathroom meets the floor tile, it is necessary to seal the joins with a silicone rubber caulking. This is important as the installation can move sufficient to crack an inflexible seal, triggering the water to pass through the wall in between the bath as well as the tiling, leading to complications with moisture and also possible leakages to the ceiling below.
You can pick from a variety of coloured sealers to blend in your components and also fittings. They are marketed in tubes and also cartridges, as well as are capable of securing gaps as much as a size of 3mm (1/8 inch). If you have a larger space to fill, you can fill it with spins of soaked newspaper or soft rope. Keep in mind to always fill up the bath tub with water before securing, to allow for the motion experienced when the bathtub is in use. The sealer can fracture relatively early if you do not take into consideration this movement before sealing.
Conversely, ceramic coving or quadrant tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are also quickly readily available on the marketplace. It is advisable to fit the tiles utilizing waterproof or waterproof sticky as well as cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I hope you liked our part about How to Install a Bathtub. Many thanks for taking a few minutes to browse our article. Are you aware of anybody else who is serious about the subject? Please feel free to share it. Thanks for your time. Come back soon.
Source