In this article down the page you can find a lot of excellent material around Installing A Bathtub.
Setting up a tub isn't precisely brain surgery, however it does call for strong plumbing, carpentry, and also often, tiling skills. Changing an old tub with a new one is additionally a moderately difficult task. If the old tub is conveniently available, the task can move speedily; if you have to open up a wall to get rid of the old tub and place the new bath tub, the job is much harder. In either situation, the project is within a residence handyman's abilities, although you will require a helper to leave the old tub and also set in the brand-new one. Ensure you have actually qualified on your own for the job and also are comfortable trying it. Instead of hiring a service provider to take over a halfway-completed task, it is better to take into consideration employing one before you begin. Opportunities are you may require a professional plumber to make tube links.
This write-up will aid you install a brand-new bathtub in your shower room if you have actually already acquired a new bathtub and also don't require to change the plan of your previous water pipes.
Your tools and also material checklist must comprise the following:
Planning for the Installment
Firstly, the supporting structure provided with the bath must be fitted (if called for) according to the manufacturer's directions. Next off, fit the faucets or mixer to the bathtub. When fitting the tap block, it is necessary to make sure that if the faucet comes with a plastic washer, it is fitted between the bath as well as the taps. On a plastic bath, it is likewise practical to fit a sustaining plate under the faucets system to avoid stress on the bathtub.
Fit the flexible tap ports to the bottom of both faucets using 2 nuts and also olives (occasionally supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and after that pass the outlet with the hole in the bath. Use the nut provided by the producer to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the versatile overflow pipe to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which ought to be fitted inside the bathroom. Make sure you make use of all of the provided washers.
Attach the trap to the bottom of the waste outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the outlet. Link the bottom of the overflow tube in a comparable manner.The bathroom need to now prepare to be fitted in its final placement.
Removing Old Taps
If you require to replace old faucets with brand-new ones as a part of your setup, after that the first thing you ought to do is detach the water system. After doing so, switch on the taps to drain any water remaining in the system. The procedure of getting rid of the existing taps can be quite problematic due to the restricted access that is typically the situation.
Utilize a basin wrench (crowsfoot spanner) or a tap tool to undo the nut that connects the supply pipelines to the faucets. Have a fabric all set for the remaining water that will come from the pipes. When the supply pipelines have actually been eliminated, make use of the very same tool to loosen up the nut that holds the faucets onto the bath/basin. You will need to quit the solitary taps from turning during this procedure. Once the taps have actually been eliminated, the holes in the bath/basin will certainly have to be cleansed of any old securing compound.
Before going on to fit the new faucets, compare the pipe links on the old faucets to the new faucets. If the old taps are longer than the brand-new taps, after that a shank adapter is required for the brand-new taps to fit.
Mounting the Bathtub
Making use of both wooden boards under its feet, position the tub in the called for setting. The wood boards are valuable in equally spreading the weight of the tub over the area of the boards rather than concentrating all the weight onto four little factors.
The following goal is to make sure that the bathtub is leveled all round. This can be attained by inspecting the level as well as adjusting the feet on the bathtub till the spirit level reviews level.
To mount taps, fit all-time low of the furthest adaptable tap adapter to the suitable supply pipeline by making a compression join; after that do the same for the various other tap.
Turn on the water supply and also check all joints as well as new pipework for leaks and also tighten them if required. Load the bathtub and additionally check the overflow electrical outlet as well as the normal electrical outlet for leaks.
Lastly, fix the bathroom paneling as described in the maker's instruction manual. Tiling and also sealing around the bath tub should wait till the bathtub has actually been used at the very least when as this will resolve it into its last position.
Suitable New Touches
If the tails of the brand-new taps are plastic, after that you will require a plastic connector to avoid damage to the string. One end of the connector fits on the plastic tail of the tap as well as the other end supplies a connection to the current supply pipes.
If you require to fit a monobloc, then you will certainly need lowering couplers, which links the 10mm pipeline of the monobloc to the conventional 15mm supply pipeline.
Next, place the tap in the placing hole in the bath/basin making certain that the washers remain in place in between the tap as well as the sink. Secure the tap in position with the producer given backnut. Once the faucet is firmly in place, the supply pipelines can be connected to the tails of the faucets. The faucets can either be linked by utilizing corrugated copper piping or with normal faucet adapters. The former kind should be linked to the faucet ends first, tightening up only by hand. The supply pipes can later on be connected to the various other end. Tighten up both ends with a spanner after both ends have been linked.
Tiling Around the Bath tub
In the area where the bathroom fulfills the tile, it is needed to secure the joins with a silicone rubber caulking. This is important as the fitting can relocate sufficient to break a stiff seal, creating the water to penetrate the wall in between the bathroom and the tiling, resulting in issues with dampness and also feasible leakages to the ceiling below.
You can choose from a variety of coloured sealants to blend in your fixtures and fittings. They are sold in tubes and cartridges, and are capable of sealing gaps up to a width of 3mm (1/8 inch). If you have a larger gap to fill, you can fill it with twists of soaked newspaper or soft rope. Remember to always load the bath tub with water prior to securing, to permit the activity experienced when the bathtub remains in use. The sealant can break fairly early if you do not consider this movement before sealing.
Conversely, ceramic coving or quadrant floor tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as cut to size, are additionally conveniently readily available on the marketplace. It is advisable to fit the floor tiles utilizing water-resistant or water-proof sticky as well as grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
We hope you enjoyed our post on Installing A Bathtub. Thank you so much for taking time to browse our posting. Are you aware of anybody else who is looking into the topic? Feel free to share it. Many thanks for your time. Come back soon.
Click Here!